P2155 Fuel Injector Group D Circuit/Open
OBD-II Trouble Code Technical Description
Red Seal Certified Technician
Fuel Injector Group D Circuit/Open
What does that mean?
This is a generic powertrain diagnostic trouble code (DTC) and typically applies to OBD-II vehicles. That may include but is not limited to vehicles from Dodge Ram (Cummins), GMC Chevrolet (Duramax), VW, Audi, Ford (Powerstroke), Mercedes Sprinter, Peugeot, Alfa Romeo, Nissan, Saab, Mitsubishi, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
Fuel injectors are an integral part of the fuel delivery systems in modern day vehicles.
Fuel delivery systems use varying amounts of components to control and monitor the volume, timing, pressures, etc. of the system in conjunction with the ECM (Engine Control Module). Fuel injectors were introduced as a replacement to the carburetor because injectors are more efficient and effective in controlling fuel delivery. As a result, they have improved our fuel economy, and engineers have been actively designing more ideal ways to increase efficiency to this design.
Given the fact that the injector's spray is controlled electronically, supply voltage is crucial in supplying fuel to the cylinders. That said, a problem in this circuit can and/or will cause significant drivability issues among other potential hazards/symptoms.
The group letter "D" in this code is used to distinguish what exact circuit the fault is referring to. To determine how this applies to your particular vehicle, you will need to refer to manufacturer specific technical information. Some examples of distinctions with injectors: Bank 1, 2, etc., paired injectors, individual injectors, etc.
The ECM illuminates the MIL (Malfunction Indicator Lamp) with P2155 and/or related codes (P2156, P2157) when it monitors a fault within the supply voltage to the fuel injectors and/or their circuits. The fact that the fuel injectors' harnesses are routed in close proximity to extreme temperatures should be noted. Because of the location of the harnesses, they are volatile to physical damage. With this in mind, I will say, most of the time, this will be a mechanical issue.
The P2155 Fuel Injector Group D Circuit/Open code is active when the ECM detects a open or malfunction within the fuel injector's supply voltage circuit.
What is the severity of this DTC?
Pretty severe I would say. In the field, we call a lack of fuel in the mixture being burnt, a "lean" condition. When you engine is running lean, you run the risk of causing extreme engine damage in both the immediate and distant futures. With that in mind, always keep up on your engine's maintenance. There needs to be a certain amount of diligence here, so let's keep our engines running smooth and efficient. After all, they ARE pulling our weight around to transport us on a daily basis.
What are some of the symptoms of the code?
Symptoms of a P2155 trouble code may include:
- Erratic engine performance
- Fuel economy reduced
- Erratic idle
- Excessive smoke
- Engine noise(s)
- Lack of power
- Cannot climb steep hills
- Reduced throttle response
What are some of the common causes of the code?
Causes for this P2155 fuel injector group supply voltage code may include:
- Defective or damaged fuel injector(s)
- Damaged wiring harness
- Internal wiring malfunction
- Internal ECM issue
- Connector problem
What are some P2155 troubleshooting steps?
Basic Step #1
First recommended step is to locate which "group" of sensors the manufacturer is referring to. With this information, you can then find the physical location of the injector(s) and their circuits. This may involve removing numerous engine covers and/or components to gain visual access (if possible). Make sure to inspect the harness for broken wires. Any worn-away insulation should be properly repaired with shrink-tube to prevent further and/or future issues.
Basic Step #2
At times, water and/or fluids may get "trapped" in the valleys where the injectors are installed. This increases the odds of the sensor's connectors, among other electrical connections, to corrode at a faster than normal rate. Make sure everything is how it should be and the connectors tabs are properly sealing the connection. Don't hesitate using some electrical contact cleaner to make everything connect and disconnect smoothly, not to mention the increased electrical connectivity within the connections with the use of this product.
Basic Step #3
Verify the integrity of the circuit by following troubleshooting steps provided by your specific vehicle's service manual. One example is to disconnect the supply voltage circuit from the ECM and at the fuel injector, then using your multimeter, determine whether or not the wires are in good working order.
One test I like to do to determine quickly if there is an open within a particular wire which would help with code P2155 is to do a "continuity test". Setting your multimeter to RESISTANCE (a.k.a.: ohm, impedance, etc.), touch one end to one tip of the circuit and the other end at the other tip. Any higher then desired value may indicate a problem within the circuit. Any issue here will need to be determined by tracing the particular wire you are diagnosing.
Related P2155 DTC Discussions
- There are currently no related topics in our forums. Post a new forum topic now.
Need more help with a P2155 code?
If you still need help regarding the P2155 trouble code, please post your question in our FREE car repair forums.
NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.