P2105 Throttle Actuator Control System - Forced Engine Shutdown
OBD-II Trouble Code Technical Description
Former Service Manager & Air Force Mechanic
Throttle Actuator Control System - Forced Engine Shutdown
What does that mean?
This generic powertrain diagnostic trouble code (DTC) typically applies to all OBD-II equipped vehicles that use a drive-by-wire throttle control system including but not limited to vehicles from Ford, GMC, Hyundai, Land Rover, Toyota, Dodge, Chevy, Subaru, Suzuki, Jaguar etc. Anecdotally this code seems to be more commonly seen on Ford, Chevrolet, and Land Rover vehicles.
The P2105 OBD-II trouble code is one of number of possible codes that indicates that the Powertrain Control Module (PCM) has detected a malfunction and is limiting the operation of the Throttle Actuator Control System
This situation is known as activating a fail-safe or limp mode to prevent the engine from accelerating until this malfunction is corrected and the associated code is cleared. There are four codes that are referred to as force codes and they are P2104, P2105, P2106 and P2110.
The PCM sets these when other codes are present that indicate an issue that may be safety related or cause damage to the engine or drivetrain components if not corrected in a timely manner.
Code P2105 is set by the PCM to force the Throttle Actuator Control System to shut the engine down.
This code can be related to a Throttle Actuator Control System malfunction, but normally another issue is setting this code. Trouble code P2105 is triggered by the PCM when it receives an abnormal signal from various components. The Throttle Actuator Control System is duty cycle controlled by the PCM and the function of the system is limited when other fault codes are detected.
Code Severity & Symptoms
The severity of this code can be moderate to severe based on the specific malfunction. Symptoms of a P2105 trouble code may include:
- Engine will not start
- Little or no throttle response
- Check Engine Light illuminated
- ABS Light illuminated
- Automatic transmission will not shift
- Additional codes are present
Common Causes Of This DTC Code
The most common situations that set this code and place the engine in fail-safe or limp mode to indicate an issue and act as a red flag are:
- Engine Overheating
- Coolant Leaks
- EGR Valve Malfunction
- Mass Air Flow Sensor Malfunction
- Drive Axle Modifications
- ABS, Traction Control or Stability Control Failures
- Automatic Transmission Problems
- Abnormal System Voltages
What are some common repairs?
- Repair coolant leak
- Replacing or cleaning ABS sensor
- Replacing or cleaning EGR Valve
- Replacing or cleaning Mass Airflow sensor
- Cleaning corrosion from connectors
- Repairing or replacing wiring
- Flashing or replacing PCM
Diagnostic and Repair Procedures
The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSB's) for the specific vehicle by year, model and power plant. In some circumstances this can save a lot of time in the long run by pointing you in the right direction.
The second step for this code is to complete a PCM scan to identify other trouble codes. This code is an informational code and in most circumstances this code’s function is to alert a driver that the PCM has initiated a fail-safe mode because of a malfunction or failure in a system that is not directly related to the Throttle Control Actuator.
If other codes are identified you should check for TSB's related to the specific vehicle and that code. If a TSB has not been generated you should follow the specific troubleshooting steps for that code to pinpoint the source of the malfunction that the PCM is detecting to put the engine in fail-safe or limp mode.
Once all other codes have been cleared or if no other codes are detected, if the Throttle Control Actuator code still exists the PCM and Throttle Control Actuator should be evaluated. All wiring and connections should be visually inspected for obvious defects as a starting point.
Replacing the Throttle Control Actuator or PCM when other malfunctions are setting this code.
Replace Throttle Actuator Control
Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your Throttle Actuator Control System force code. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.
Here are links to some discussions of Ford vehicles with the P2105 code:
Related P2105 DTC Discussions
- no start , range rover 07 hse 4.4 U0151 p0222, p0122, p2105
Gm !! having a problem with a no start, cranks n cranks no start...code U0151 restrains no communication... would this cause a no start... or po222, po122 , po2105.. need help thanks,.....
Need more help with a p2105 code?
If you still need help regarding the P2105 trouble code, please post your question in our FREE car repair forums.
NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected. If you want to share this article or information with others, please link to this page, don't copy and paste it elsewhere.