P2024 EVAP Fuel Vapor Temp Sensor Circuit
OBD-II Trouble Code Technical Description
Red Seal Certified Technician
Evaporative Emissions (EVAP) Fuel Vapor Temperature Sensor Circuit
What does that mean?
This is a generic powertrain diagnostic trouble code (DTC) and typically applies to OBD-II vehicles. That may include but is not limited to vehicles from Mercedes Benz, VW, Audi, Subaru, Chevy, Dodge, BMW, Suzuki, Hyundai, Sprinter, etc. Anecdotally this code seems to be more commonly found on Mercedes-Benz vehicles.
Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
The Evaporative emissions (EVAP) system was introduced to vehicles for a few different reasons. Some of those included but are not limited to: reduced emissions expelled, slightly improved fuel efficiency, containing otherwise wasted fuel vapors. Not to mention consistently recycling unused/unburned fuel, pretty efficient isn't it?
That being said, the EVAP system requires a multitude of sensors, switches, and valves in order to maintain desired emissions. The ECM (Engine Control Module) actively monitors these and adjusts them according to system needs. Just as the name implies, the fuel vapor temperature sensor is used by the ECM to monitor the temperature of those unburned vapors that would otherwise be expelled to the atmosphere.
It is important to note that the EVAP system uses mostly plastic components to deliver the unburned fuel vapors to the engine to be burnt. You can imagine what kind of issues can occur when you expose plastic to the elements 24/7. Especially in particularly harsh winter conditions, these plastic components tend crack/split/break/clog. Food for thought.
The check engine light gets activated with P2024 and associated codes P2025, P2026, P2027, and P2028, when the ECM recognizes one or more electrical values missing and/or outside of a specific range within the EVAP fuel vapor temperature sensor or in one of the circuits involved. Hard to say wether this would be mechanical or electrical, the thing to keep in mind is, the overall health of the system involved, in this case, the EVAP system, is and always should be the priority.
Code P2024 is activated when the ECM monitors a general malfunction within the EVAP fuel vapor temperature sensor circuit
What is the severity of this DTC?
As with most EVAP faults, I would say this is low on the severity scale. The entire system was mostly designed to decrease emissions to the atmosphere. Obviously it does a lot more in the meantime but all that being said, really the only thing negatively affected by this fault is the atmosphere. At the moment, I cannot think of any EVAP system problem that would be detrimental to the overall safety of the vehicle. This does NOT mean you can continue to drive the vehicle day in day out without addressing the issue. One problem always leads to another if left unsolved for too long.
What are some of the symptoms of the code?
Symptoms of a P2024 trouble code may include:
- Failed state/provincial emission test
- CEL (check engine light) on
- Slight decrease in fuel efficiency
- Fuel smell
- Possible abnormal fuel filling symptoms (lengthy fill ups, cannot pull trigger on gas pump fully, etc.)
What are some of the common causes of the code?
Causes for this P2024 fuel trim code may include:
- Defective EVAP (Evaporative emissions) fuel vapor temperature sensor
- Obstruction/leak within system causing sensor to perform out of range (mainly P2025)
- Broken or damaged EVAP fuel vapor temperature sensor wiring harness
- Wire shorting to power
- Excessive resistance within the circuit
- ECM (Engine Control Module) issue
- Pin/connector problem. (corrosion, melting, broken lock tab etc..)
How do I troubleshoot and repair a P2024 code?
Like mentioned above, the general health of the EVAP (Evaporative Emissions) system's health is of great importance. Verify that the components involved are free of obstruction and there are no visible cracks in the plastic pipes. It would be a good idea to locate where the EVAP system gets its fresh atmospheric air to introduce into the system to regulate pressure differences. In some instances, most of the parts used in this system will be located under the vehicle. I'd recommend using wheel ramps rather then a hydraulic jack and stands for their convenience and most importantly the safety benefits.
NOTE: Be careful when disconnecting/manipulating EVAP pipes and hoses. A lot of times they may look healthy until you try to disconnect them and a clip or the entire pipe breaks and now you need to replace/repair something to move further in your diagnostics. Be extremely prudent here.
Test the sensor. From my experience, the ECM uses voltages readings from the EVAP fuel vapor temperature sensor to monitor temps. That being said, there is most likely a specific pin-out test that can be performed to verify the functionality of the sensor.
Related P2024 DTC Discussions
- There are currently no related topics in our forums. Post a new forum topic now.
Need more help with a P2024 code?
If you still need help regarding the P2024 trouble code, please post your question in our FREE car repair forums.
NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.