OBD Codes
Your OBD-II Trouble Codes Repair Site

P07BE Transmission Park Position Sensor/Switch A/B Circuit Correlation

OBD-II Trouble Code Technical Description

Article by
John Ingalls
John Ingalls
Former Service Manager & Air Force Mechanic

Transmission Park Position Sensor/Switch A/B Circuit Correlation

What does that mean?

This is a generic powertrain diagnostic trouble code (DTC) and applies to OBD-II vehicles that have a transmission park position switch/sensor. That may include but is not limited to vehicles from Dodge, Ford, Toyota, Land Rover, VW, Chevrolet, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.

Trouble code P07BE is one of several possible codes associated to the Transmission Park Position Sensor/Switch circuit.

This code is an indication that the Powertrain Control Module (PCM) has detected a correlation problem between the "A" and "B" transmission park position sensor/switch circuits. The specific situation determines the code activated by the PCM and the check engine light or the service engine soon light will be illuminated.

The purpose of the transmission park position sensor/switch circuit is to monitor the status of the transmission. This circuit sends a signal to the PCM when the transmission is placed into the park position. Based on the specific vehicle, this circuit is commonly a safety feature to prevent the starter from engaging with the automatic transmission in gear.

Refer to a vehicle specific repair manual to determine the location of the A and B circuits in your particular application.

What is the severity of this DTC?

The severity of this code varies based on the specific malfunction and the severity level may progress if not corrected in a timely manner. This code could become a safety issue requiring immediate attention if the starter will engage with the vehicle in gear.

Photo of a park/neutral position switch:
P07BE Park Neutral Position Switch

What are some of the symptoms of the code?

Symptoms of a P07BE trouble code may include:

What are some of the common causes of the code?

Causes for this P07BE code may include:

What are some P07BE troubleshooting steps?

The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins for known issues with the specific vehicle.

Locate all of the components associated with the transmission park position sensor/switch circuits. This will include the transmission park position sensor/switch, wiring, connectors and the PCM on a simplex system. Based on the specific year, make and model of the vehicle this circuit may incorporate more components. After these components are located, a thorough visual inspection should be conducted to check all of the associated wiring and connectors for obvious defects such as scraping, rubbing, bare wires or burn spots. The connectors should also be checked for corrosion build up or damaged pins.

Advanced Steps

The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Voltage requirements will vary based of the specific year, make and model of the vehicle.

Circuit Checks

Voltage requirements will vary based on the specific vehicle, the transmission park position sensor/switch circuit configuration and the components incorporated. Technical data should be referenced to obtain the correct voltage range for the transmission park position sensor/switch and the appropriate troubleshooting sequence to follow. The correct voltage input to a sensor/switch with no voltage output is normally an indication of internal failure.

If this process identifies the absence of a power source or ground, continuity testing may be needed to check the condition of the wiring and connectors. Continuity tests are always performed with the power removed from the circuit and the normal readings should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring or connectors that are shorted or open and must be repaired or replaced.

Common Repairs

Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your the transmission park position sensor/switch circuit(s). This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.

Related P07BE DTC Discussions

Need more help with a P07BE code?

If you still need help regarding the P07BE trouble code, please post your question in our FREE car repair forums.

NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.