P0750 Shift Solenoid A Malfunction
OBD-II Trouble Code Technical Description
Former Service Manager & Air Force Mechanic
Shift Solenoid A Malfunction
What does that mean?
This is a generic transmission diagnostic trouble code (DTC) and typically applies to OBD-II vehicles equipped with an automatic transmission.
That may include but is not limited to vehicles from Chrysler, Ford, Dodge, Hyundai, Kia, Ram, Lexus, Toyota, Mazda, Honda, VW, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
Most automatic transmissions incorporate at least three solenoids that are solenoid A, B and C. The trouble codes related to this, the "A" solenoid, are codes P0750, P0751, P0752, P0753 and P0754 based on the specific malfunction that alerts the PCM to set the code and illuminate the Check Engine Light. These codes will also be associated to the A, B or C solenoid circuit. If you have an Overdrive or other transmission warning lamp, it may be illuminated also.
The purpose of the Shift Solenoid Circuit is for the PCM to monitor the shift solenoids to manage the movement of fluid between various hydraulic circuits and change the transmission gear ratio at the appropriate time. This process maximizes the performance level of the engine at the lowest RPM possible.
The automatic transmission relies on bands and clutches to change gears and this is accomplished by having fluid pressure in the right place at the right time. The transmission solenoids are responsible for opening or closing valves in the valve body to allow transmission fluid to flow to the clutches and bands to shift the transmission smoothly as the engine accelerates.
When the Powertrain Control Module (PCM) detects a malfunction within the Shift Solenoid "A" Shift Circuit a variety of codes can be triggered depending on the specific vehicle, transmission and the number of gears incorporated into the specific automatic transmission. In this case, the P0750 OBD-II trouble code is associated with a general malfunction with the the transmission Shift Solenoid "A" Circuit.
Example of shift solenoids:
What is the severity of this DTC?
The severity of this code normally starts as moderate, but it can progress to a more severe level rapidly when not corrected in a timely manner.
What are some of the symptoms of the code?
Symptoms of a P0750 trouble code may include:
- Transmission slipping
- Transmission overheating
- Transmission catches in gear
- Decreased fuel economy
- Possibly misfire-like symptoms
- Vehicle enters limp mode
- Check Engine Light illuminated
What are some of the common causes of the code?
Causes for this P0750 transmission code may include:
- Insufficient fluid level
- Dirty or contaminated fluid
- Dirty or clogged transmission filter
- Defective transmission valve body
- Restricted hydraulic passages
- Transmission has internal failure
- Faulty shift solenoid
- Corroded or damaged connector
- Faulty or damaged wiring
- Faulty PCM
What are some P0750 troubleshooting steps?
Prior to beginning the troubleshooting process for any malfunction you should research the Technical Service Bulletins (TSB's) for the specific vehicle by year, model and transmission. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. You should also check the vehicle records to verify the last time that the filter and fluid was changed if possible.
Fluid & Wiring Inspections
The first step is to make sure the fluid level is correct and inspect the condition of the fluid for contamination. Then, a thorough visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots should be performed.
Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring and connectors to the transmission solenoids, transmission pump and the PCM. Based on the configuration, the transmission linkage should be inspected for security and binding issues.
The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Voltage requirements will very based of the specific year and model of the vehicle. You should follow the specific troubleshooting chart for your vehicle.
Continuity checks should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.
What are some common repairs for this code?
- Changing the fluid and filter
- Repair or replace a faulty shift solenoid
- Repair or replace defective transmission valve body
- Repair or replace defective transmission
- Transmission flush to clean passages
- Cleaning corrosion from connectors
- Repairing or replacing wiring
- Flashing or replacing PCM
Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your Shift Solenoid Circuit fault code. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.
Related P0750 DTC Discussions
- Ford Focus P0750
I've got a 2002 Ford Focus that's showing a P0750 (Shift Solenoid A malfunction). Starts normally and then drops into neutral after a short distance (1/4 mile or less). If I drive in 2nd gear it stays in gear or if I lock out the OD it seems to go normally (obviously with no OD). It has about 72k...
- 2007 PT Cruiser: OBD Codes: P0700, P0750, and P0463
I have a 2007 PT Cruiser w/ 2.4L inline 4 cyl. and an AT that seems to be in 'limp mode.' The transmission will only stay in 2nd gear when i drive . Also the fuel guage acts up by showing empty or full. Anyone have any idea if these problems can be fixed given the OBD codes?...
- 01 Dodge Caravan P0750, P1782, P0700, P0760, P0755
2001 Dodge Caravan V6 3.3L pulling in multiple tranny codes. Only work that has been done was a tune up in the summer time, tranny had ran fine, didn't slip or shift hard. Right now it is in limp in mode. Drive only has 2 gears, 1, 2 & reverse.. I have changed the tranny fluid/filter with correc...
- 2003 Ford Explorer P0713 P0731 P0733 P0750 P0753 P0755 P0758 P0760 P0763 etc.
During a short stop for a traffic light, my Vehicle suddenly switched off, when I switched on again and I moved the transmission to the "D", it was too heavy and it's moving a little bit even when I increase the fuel, the O/D is flashing now. I checked my Vehicle, and they told me that you...
- p0700 p1768 and p0750 trouble codes, 2000 jeep grand cherokee
i have a 2000 jeep grand cherokee. i have replaced both the input and output sensors, and replaced the soleniod pack in the transmission. problem still exists. no first gear and no overdrive. im still getting the codes p0700 p0750 and p1768. can someone please tell me what these codes have in c...
- 2001 Ford F450 P0750, P0443, P1747, P0755, P0743
2001 Ford F450 V10, fault codes P0750, P0443, P1747, P0755, P0743. I've read each code description, but i'm unclear on witch one may be causing my problem. The truck runs good at idle, but flutters and barely moves once it is put into drive or reverse. If a load is applied, like going up a hill or s...
- 2002 Mercury Sable Codes P0743 P0750 P0760
we recently purchase grandma's 02 sable with 60k miles. it has experienced minor erratic shifting the last month or so. when pulling away from a stop sign the transmission disengaged and the car wouldn't move. nothing happens when you run the shifter through all the gears. the fluid looks and smells...
- 2001 mercury sable codes P1747 P0743 P0750 P0760 P1451
Hi, If I just had my front axle and brakes repaired could this make these codes appear? Thank you, Botelho's...
- 2000 Dodge Grand Caravan pulling codes P0700 P0760 P0750
went into limp mode so ran codes PO700 and PO760 so replaced OD shift selonoid block check engine light went out drove short distance and came back on reading code PO700 and PO750 what should I do now?...
- Lincoln LS 2003 with P0132 P0750 P0966 P2196 P0755 P0760
I have a 2003 Lincoln ls 3.0 I just replaced the motor and now getting multiple observed codes for the transmission. Po755 po743 po760 po132 po750 po966 p2196. Before replacing the motor there was no transmission codes. The car has no power and doesn't want to go. My mechanic says a brand new trans...
Need more help with a P0750 code?
If you still need help regarding the P0750 trouble code, please post your question in our FREE car repair forums.
NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.