OBD Codes
Your OBD-II Trouble Codes Repair Site

P0259 Injection Pump Fuel Metering Control B High

OBD-II Trouble Code Technical Description

Article by
Randy
Randy Worner
ASE Certified Master Technician

Injection Pump Fuel Metering Control B High (Cam/Rotor/Injector)

What does that mean?

This generic powertrain/engine diagnostic trouble code can typically apply to all diesel fueled OBD-II equipped engines (e.g. Ford, Chevy, GMC, Ram, etc.), but shows up more often in certain Mercedes Benz and VW vehicles.

Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.

The Injection Pump Metering Control Circuit "B" is usually found mounted inside / on the side of the injection pump bolted to the engine. The Injection Pump Metering Control Circuit "B" is usually made up of a Fuel Rack Position (FRP) Sensor and a Fuel Quantity Actuator.

The FRP sensor converts the amount of diesel fuel being delivered by the Fuel Quantity Actuator to the injectors into an electrical signal for the Powertrain Control Module (PCM).

The PCM receives this voltage signal to determine how much fuel it will put into the engine based upon engine operating conditions. This code is set if this input does not match normal engine operating conditions stored in the PCM’s memory, even for a second, as this diagnostic trouble code demonstrates. It also looks at the voltage signal from the FRP sensor to determine if it is correct at initial Key On.

The code P0259 Injection Pump Fuel Metering Control B High (Cam/Rotor/Injector) is set when the voltage at the sensor stays above a set level (usually over 4.8V) for too long a period. This code is usually considered to be an electrical circuit issue. Refer to a vehicle specific repair manual to determine which is the "B" part of the circuit for your particular application.

Troubleshooting steps may vary depending upon manufacturer, type of FRP sensor and wire colors.

What is the severity of this DTC?

Severity in this case will be not severe. Since it is electrical failure, the PCM can compensate adequately for it.

What are some of the symptoms of the code?

Symptoms of a P0259 trouble code may include:

What are some of the common causes of the code?

Causes for this P0259 code may include:

What are some P0259 troubleshooting steps?

A good starting point is always to check for technical service bulletins (TSB) for your vehicle. Your issue may be a known issue with a known fix put out by the manufacturer and can save you time and money during diagnosis.

Next, locate the FRP sensor on your vehicle. This sensor is usually found usually found mounted inside / on the side of the injection pump bolted to the engine. Once located, visually inspect the connector and wiring. Look for scraping, rubbing, bare wires, burn spots or melted plastic. Pull the connector apart and carefully inspect the terminals (the metal parts) inside the connector. See if they look burned or have a green tint indicating corrosion. Use electrical contact cleaner and a plastic bristle brush if cleaning of the terminals is needed. Let dry and apply electrical grease where the terminals contact.

If you have a scan tool, clear the diagnostic trouble codes from memory, and see if P0259 code returns. If it does not, then the connections were most likely your problem.

If the P0259 code does return, we will need to test the FRP sensor and its associated circuits. With the Key Off, disconnect the electrical connector at the FRP sensor. Connect a Digital Voltmeter black lead to the ground terminal at the FRP sensor wiring harness connector. Connect the red lead of the Digital Voltmeter to the power terminal at the FRP sensor wiring harness connector. Turn Key On Engine Off. Check manufacturer’s specifications; voltmeter should read either 12 volts or 5 volts. If not, repair the power or ground wire, or replace the PCM.

If the prior test passed, we will need to test the signal wire. With the connector still disconnected, move the red lead of the voltmeter from the power wire terminal to the signal wire terminal. The voltmeter should now read 5 volts. If not, repair the signal wire, or replace the PCM.

If all prior tests have passed and you continue to get a P0259, this would most likely indicate a failed FRP sensor / Fuel Quantity Actuator, although a failed PCM could not be ruled out until the FRP sensor / Fuel Quantity Actuator had been replaced. If unsure, seek assistance from a trained automotive diagnostician. PCMs must be programmed, or calibrated to the vehicle to be installed correctly.

Related P0259 DTC Discussions

Need more help with a P0259 code?

If you still need help regarding the P0259 trouble code, please post your question in our FREE car repair forums.

NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.